UV Aging
UV, condensation and spray.
About Dexiang — Aging Test Chamber Manufacturer
Engineering and manufacturing aging test chambers for controlled, repeatable material and component reliability testing.
AGING TEST CHAMBER MANUFACTURER
Aging test chambers engineered around how materials and components fail over time.
Founded in 2022, Dexiang is an aging test chamber manufacturer serving laboratories, manufacturers and quality teams that need controlled light, heat, humidity and pressurized-moisture exposure. We connect the required method, specimen, cycle and acceptance evidence to a standard chamber or engineered configuration.
Xenon Weathering
Full-spectrum light and climate.
HAST & PCT
Unsaturated or saturated pressure aging.
Temperature-Humidity
Steady and programmed climate aging.
Shared Dongguan manufacturing resources
Dexiang shares its Dongguan production base, R&D team, assembly lines and after-sales team with Deruitest, while Dexiang remains the company and brand presented on this website.
Company reach
2022: Dexiang established
3,000+: customers served
100+: countries reached
Different failure risks require different aging-test routes.
The word “aging” does not define one test. Selection begins with the degradation mechanism and required exposure.
UV aging
For cracking, chalking, fading and gloss loss driven by fluorescent UV and moisture cycles. Review lamp, irradiance, panel temperature, condensation and spray.
Xenon weathering
For colour and material response requiring filtered full-spectrum light. Review irradiance point, filters, temperature, RH, spray and specimen capacity.
Temperature-humidity aging
For moisture ingress, corrosion, insulation change and distortion under steady or cyclic climate. Review profile, heat load, airflow and workspace.
HAST versus PCT
HAST uses controlled unsaturated humidity; PCT uses saturated steam. They are separate methods and must not be substituted merely because both use pressure.
Important: the chamber creates exposure conditions; service-life correlation still depends on the method, specimen preparation, evaluation and acceptance criteria.
FROM METHOD TO CONFIGURATION
A useful quotation starts with the test requirement—not a catalogue number.
01 Method
Standard, setpoints, sequence, duration and acceptance.
02 Specimen
Size, mass, quantity, material, fixture and powered state.
03 Control
Light, temperature, RH, pressure, spray, ramp and data.
04 Site
Power, water, drainage, ventilation, calibration and FAT.
| Input | Why it matters | Proposal output |
|---|---|---|
| Method and cycle | Defines controllable parameters and options. | Architecture and control functions. |
| Specimen load | Changes workspace, holders and performance. | Model, capacity and fixture. |
| Utilities and evidence | Changes installation and documentation. | Site schedule and acceptance package. |
ENGINEERING AND CUSTOMIZATION
Customization is linked to a real method, specimen or site requirement.
Workspace & fixtures
Capacity, shelves, holders, orientation and access.
Control & data
Programs, interfaces, export, alarms and remote access.
Ports & bias
Feedthroughs and terminals defined by channels, voltage and current.
Utilities
Destination power, water, drainage, air and cooling.
Safety
Interlocks and independent protection matched to risk.
Documents
Drawings, manuals, calibration and FAT scope.
A feature is described as standard only when the selected model and final order specification confirm it.
MANUFACTURING AND VERIFICATION
The confirmed specification guides assembly, checks and acceptance.
01 Freeze scope
Confirm model, performance basis, options and documents.
02 Assemble
Build chamber, controls, circuits, fixtures and safeguards.
03 Check
Review controls, programs, alarms and interlocks.
04 Handover
Reconcile machine, accessories and agreed evidence.
PRODUCT PORTFOLIO
A focused portfolio for light, climate and pressure-moisture aging.
UV Aging Test Chambers
Tower and cabinet configurations for fluorescent UV, condensation and spray.
Xenon Arc Weathering Chambers
Air- and water-cooled configurations for full-spectrum weathering.
High-Pressure Aging Chambers
Unsaturated HAST and saturated PCT routes.
Temperature & Humidity Chambers
Benchtop, cabinet and walk-in climatic-aging configurations.
DELIVERY AND SUPPORT
Plan installation and handover before the chamber arrives.
20–30 days
Typical standard-machine lead time after scope confirmation.
30–45 days
Typical non-standard lead time, subject to engineering scope.
1-year warranty
Under agreed warranty terms and operating conditions.
Installation
Installation and commissioning arrangements by project scope.
Training
Operation, programs, safety and routine maintenance.
Export packing
Machine and accessories protected in an export wooden crate.
Export packing and shipmentShow the protected chamber and export wooden crate.
CERTIFICATIONS AND FACTORY EVIDENCE
Trust should be supported by current, scope-matched evidence.
Dexiang can present ISO 9001 and CE documents together with available calibration or testing capability evidence. Applicability must be checked against issuer, scope, model and destination.
Factory and assemblyReplace with real Dongguan production photographs.
Inspection and FATUse real curves, screens and acceptance records.
ISO 9001 and CEShow legible, current and applicable documents.
Calibration capabilityShow equipment or report evidence without overstating scope.
Machine detailsShow workspace, controller, safeguards and fixtures.
PackingShow accessory reconciliation and export crate.
Replace every placeholder with a real asset before the page goes live.
DISCUSS YOUR AGING TEST REQUIREMENT
Send the method and specimen—not just a chamber name.
Provide the method, specimen dimensions and quantity, exposure cycle, heat or bias load, utilities, destination power and required acceptance documents.
- Test standard or customer procedure
- Specimen drawing, mass, quantity and fixture
- Required light, temperature, humidity, pressure or spray
- Data, communications, calibration and FAT requirements
